Products

微型无槽直流无刷电动机

26BC 3C - 微型无槽直流无刷电动机

26BC 3C

26BC 无刷无槽电机采用自支撑圆筒形空心杯线圈,这种线圈是采用与我们的空心杯直流电机相同的绕组技术制成的。26BC 微型电机具有长寿命、优异的速度和位置控制以及平稳的转动。

性能及特点

  • 紧凑的设计

  • 无槽

  • 2 极

  • 紧凑的设计

  • 高速下的低铁损

  • 高效

  • 3 相

按需求定制

  • 轴长度
  • 特殊线圈
  • 电缆和连接器
  • 特殊安装方式

典型应用

规格+细节
文件
公制 英制单位
Winding{%|%}unit 26BC 3C 109P .101
Diameter{%|%}in 1.06
Diameter{%|%}mm 26
Length{%|%}in 1.27
Length{%|%}mm 32.30
Nominal Voltage{%|%}Volt 12.0
Optimization Speed
No-Load Speed{%|%}rpm 14,800
Typical No-Load Current{%|%}mA 180
Max continuous mechanical power (@ 25°C){%|%}W 8.0
Max continuous Current{%|%}A 0.8
Max Continuous Torque{%|%}mNm 7.00
Max Continuous Torque{%|%}oz-in 0.99
Terminal Resistance{%|%}Ω
Output Power{%|%}W
Stall Torque{%|%}oz-in
Stall Torque{%|%}mNm
Efficiency{%|%}%
Speeds up to{%|%}rpm
Torque up to{%|%}oz-in
Torque up to{%|%}mNm
Current up to{%|%}thermal limits
Back-EMF Constant{%|%}V/1000 rpm 0.73
Torque Constant{%|%}mNm/A 7.00
Torque Constant{%|%}oz-in/A 0.99
Motor Regulation R/k²{%|%}10³/Nms 102.04
Motor Constant k/R½{%|%}mNm/W½ 3.1
Motor constant k/R½{%|%}oz-in/W½ 0.44
Internal resistance - phase to phase{%|%}Ω 5.00
Line to Line resistance at connectors{%|%}Ω 5.00
Inductance - phase to phase{%|%}mH 0.09
Friction Torque{%|%}onz-in
Friction Torque{%|%}mNm
Rotor Inductance (mH)
Mechanical Time Constant{%|%}ms 95.0
Electrical time constant{%|%}ms 0.02
Max motor speed{%|%}rpm 20,000
Ambient working temperature range{%|%}°C 0 / + 70
Ambient working temperature range{%|%}°F +32/+158
Ambient storage temperature range{%|%}°C 0 / + 70
Ambient storage temperature range{%|%}°F +32/+158
Ball bearings preload{%|%}N 5.0
Axial static force without shaft support{%|%}N 45
Max Winding Temperature{%|%}°C
Max winding temperature{%|%}°C 125
Max Winding Temperature{%|%}°F
Max winding temperature{%|%}°F 257
Thermal Resistance{%|%}°C/W 14
Thermal Time Constant{%|%}s 660
Operating Temperature Range{%|%}°F
Weight{%|%}oz 2.54
Weight{%|%}g 72
Rotor Inertia{%|%}gcm²
Rotor Inertia{%|%}gcm² 9.4
Typical Housing Material Aluminium alloy / plastic
Hall Sensor Elecrical Phasing{%|%}electrical °
Absolute accuracy 2 ph. On, Full step mode (degree)
Bearing Type
Detent Torque, Max (mNm)
Detent Torque, Max (oz-in)
Dielectric Withstanding Voltage (VAC)
Holding Torque, MIN (mNm)
Holding Torque, MIN (oz-in)
Inductance per Phase, typ (mH)
Insulation Resistance at 500 VDC (Mohms)
Leadwire
Maximum Coil Temperature (C)
Maximum Coil Temperature (F)
Operating Voltage (VDC)
Rated Current per Phase, 1 Phase ON (A)
Resistance per Phase, ± 10%{%|%}Ohms
Rotor Inertia{%|%}oz-in-sec²10^-6
Continuous Stall Current{%|%}A
Peak Torque for 1s{%|%}mNm
Peak Torque for 1s{%|%}oz-in
Peak Current{%|%}A
Max Axial Shaft Load (N)
Max Axial Shaft Load (oz)
Max Radial Shaft Load (N)
Max Radial Shaft Load (oz)
Shaft Load Max Axial{%|%}lb
Shaft Load Max Axial{%|%}N
Shaft Load Max Radial{%|%}lb
Shaft Load Max Radial{%|%}N
Steps per Revolution
Back EMF Amplitude (V/ksteps/s)
Nominal Phase Current (1 ph. On) (A)
Nominal Phase Current (2 ph. On) (A)
Angular Acceleration (nominal current)
Axial Shaft Play (µm)
Holding Torque Typical (mNm)
Holding Torque Typical (oz-in)
Holding Torque, 1.5x nominal current (mNm)
Holding Torque, 1.5x nominal current (oz-in)
Natural Resonance Frequency @nominal current (Hz)
Power rate (nominal current) (kW/s)
Radial Shaft Play (µm)
Max. Force* @ .001" (0.0254 mm) / Step (N)
Max. Force* @ .001" (0.0254 mm) / Step (oz)
Max. Force* @ .002" (0.0508 mm) / Step (N)
Max. Force* @ .002" (0.0508 mm) / Step (oz)
Max. Force* @ .004"(0.1016 mm) / Step (N)
Max. Force* @ .004"(0.1016 mm) / Step (oz)
Stroke Length, Typ{%|%}mm
Stroke Length, Typ{%|%}in
Min. Holding Force (Unenergized) @ .0005" (0.0127 mm) / Step{%|%}N
Min. Holding Force (Unenergized) @ .0005" (0.0127 mm) / Step{%|%}oz
Min. Holding Force @ 0.001" (0.0254 mm) / Step (Un-energised) (N)
Min. Holding Force @ 0.001" (0.0254 mm) / Step (Un-energised) (oz)
Min. Holding Force @ 0.002" (0.0508 mm) / Step (Un-energised) (N)
Min. Holding Force @ 0.002" (0.0508 mm) / Step (Un-energised) (oz)
Min. Holding Force (Unenergized) @ 0.003" (0.0762 mm) / Step (Un-energized){%|%}N
Min. Holding Force (Unenergized) @ 0.003" (0.0762 mm) / Step (Un-energized){%|%}oz
Min. Holding Force @ 0.004" (0.1016 mm) / Step (Un-energised) (N)
Min. Holding Force @ 0.004" (0.1016 mm) / Step (Un-energised) (oz)
Min. Holding Force @ rated current @ .0005" (0.0127 mm) / Step{%|%}N
Min. Holding Force @ rated current @ .0005" (0.0127 mm) / Step{%|%}oz
Min. Holding Force @ rated current @ .001" (0.0254 mm) / Step{%|%}N
Min. Holding Force @ rated current @ .001" (0.0254 mm) / Step{%|%}oz
Min. Holding Force @ rated current @ .002" (0.058 mm) / Step{%|%}N
Min. Holding Force @ rated current @ .002" (0.058 mm) / Step{%|%)oz
Min. Holding Force @ rated current @ .003" (0.0762 mm) / Step{%|%}N
Min. Holding Force @ rated current @ .003" (0.0762 mm) / Step{%|%}oz
Min. Holding Force @ rated current @ .004" (0.1016 mm) / Step{%|%}N
Min. Holding Force @ rated current @ .004" (0.1016 mm) / Step{%|%}oz
Number of lines available
Output signal
Supply Current - maxium (mA)
Supply Current - stand-by (μA)
Supply Current - typical (mA)
Supply Voltage (V)
Direction of rotation ( = / ≠)
Max. Recommended Input Speed (rpm)
Number of gear stages
Number of lines available
Type of encoder
Linear Travel Accuracy
Input Power (W)
Stepper Type
Gear Ratio
Sterilization Cycles
Prototype Pricing
Document Technology Document Type Language File Type
26BC3C drawing 无刷直流电机 DXF图纸  
26BC 3C 3D Drawing 无刷直流电机 3D  
26BC3C Specification Sheet 无刷直流电机 规格说明  
Timing Relationship in Brushless DC Motors (diagram) 无刷直流电机 文件资料  
Timing Relationship in Brushless DC Motors (diagram: CN) 无刷直流电机 文件资料  
About Brushless DC Motors (brochure) 无刷直流电机 文件资料  
About Brushless DC Motors (brochure: CN) 无刷直流电机 文件资料